通过认证
“弯弧安全滑触线价格 弧形滑导线厂家 弧形导轨制作”参数说明
| 类型： | 绝缘配线槽 | 材质： | 德玛易通 |
| 认证： | CCC | 品牌： | 德玛易通 |
| 定尺： | 4.5米或4米或6米 | 使用环境： | 有弯弧要求轨道、设备供电线、自动化生产线 |
| 产量： | 1000000 |
“弯弧安全滑触线价格 弧形滑导线厂家 弧形导轨制作”详细介绍
弯弧安全滑触线价格弧形滑导线厂家弧形导轨制作弯弧安全滑触线越来越多的应用到工业生产过程中，可以适用于有弧度要求的移动设备中。应用较灵活，适用范围较广。德玛弯弧安全滑触线根据市场要求，在产品设计上进行优化。弯弧滑触线采用组合式结构，构造简单，安装方便，易于维护。采用铜导体作为输电导体，可以实现节能15%-20%，大大节省材料和安装费用。弯弧型安全滑触线外壳采用工程塑料作为保护，安全可靠，防雨、防尘大大延长使用寿命，适应多样化环境。弯弧型安全滑触线可以适用于功率较小的移动设备，成本低，价格优惠。德玛弯弧滑触线集电器尺寸小，在转弯过程中移动顺滑，实现不间断供电。在两段滑触线连接时，将导体延长至另一段滑触线外壳中之后再进行连接，这样集电器在运动时不会出现运行不畅，接触不良等情况。济南德玛科诺各式集电器济南德玛电气有限公司和济南科诺起重机械有限公司是集开发研究、生产制造、市场营销于一体的综合型公司。自主生产研发销售适应广泛领域使用的滑线、滑触线,滑导线；节能环保的节能滑线、节能滑导线、节能滑触线；可用于自动化生产线的移动供电滑线、移动供电滑触线、移动供电滑导线、供电滑线、供电滑触线、供电滑导线、电车滑线、电车滑触线、电车滑导线、电缆滑线、电缆滑触线、电缆滑导线；可用于起重机,行车的行车滑线、行车滑触线、行车滑导线、起重机滑线、起重机滑触线、起重机滑导线、电动葫芦滑线、电动葫芦滑触线、电动葫芦滑导线、安全滑线、安全滑触线、安全滑导线、龙门吊滑线、龙门吊滑触线、龙门吊滑导线、铝合金滑线、铝合金滑触线、铝合金滑导线、钢铝滑线、钢铝滑触线、钢铝滑导线；可用于高温、高湿、高电压强腐蚀、多粉尘环境的防尘滑线、防尘滑触线、防尘滑导线、高温钢体滑线、高温钢体滑触线、高温钢体滑导线、高温刚体滑线、高温刚体滑触线、高温钢体滑导线、钢体滑线、钢体滑触线、钢体滑导线、刚体滑线、刚体滑触线、刚体滑导线、防爆滑线、防爆滑触线、防爆滑导线、钢排滑线、钢排滑导线、钢排滑触线等新型的移动机械设备馈电的供电系统；滑线集电器、滑触线集电器、滑导线集电器、集电器、供电器、受电器、导电器、温度补偿等各种滑线配件、滑触线配件、滑导线配件；可用于厂矿、库房、码头的管式滑线、管式滑导线、管式滑触线、管式多极滑线、管式多极滑导线、管式多极滑触线、单极滑触线、单极滑线、单极滑导线等。以及起重机、行车、桥式起重机、梁式起重机、桥式行车、桥式起重机、电动葫芦、母线槽、滑触线母线、滑线母线、滑导线母线、桥架、金属桥架、电缆桥架等产品。使用特殊铝合金配方型材,节能环保,安全可靠；是济南滑线、济南滑触线、济南滑导线、山东滑线、山东滑触线、山东滑导线、起重机制造、行车制造乃至全中国滑触线、中国滑线,中国滑导线、中国起重机、中国行车、中国起重机制造、中国行车制造生产厂商中质量、性价比最高的!
“弯弧安全滑触线价格 弧形滑导线厂家 弧形导轨制作”其他说明
| 工序Serial No. of working procedure |
工序名称 Name of working procedure |
安 装 程 序 及 要 求 Installation procedure and requirements |
| 1 |
安装角钢支架 Installation of angle steel bracket |
用螺栓或焊接方式按规定间距把角钢支架固定在行车道轨垫板上（用压板螺栓压紧，或焊接在垫板上）。必须保证支架在整个线上的平直，角钢的伸出尺寸一致，角钢要平行不能歪斜。 Fix angle steel brackets on track rail tie-plate as per specified spacing by using bolt or welding method (press it tightly by using follower bolt, or weld it on tie-plate). It is essential to ensure that brackets are straight on the whole line, extruding dimensions of angle steel are identical and angle steels should be paralleled with each other rather than inclined. |
| 2 | 把悬挂架安装在角钢支架上Installation of suspension on angle steel bracket |
此时螺母不要拧紧，待调整好后再拧紧，重型线的挂架已安装在导线上。 Tighten nut after completion of readjusting rather than tighten nut immediately. Suspensions of heavy-duty line have been installed on conductive wire. |
| 3 |
安装滑触线及接头 Installation of sliding-contact wire and connector |
把滑触线装入悬挂架的卡口内卡住。四根滑触线装好后调平，旋紧挂架的螺母。把接头装入第一组滑触线的另一端，同样方法安装第二组滑触线。用接头将两根滑触线联接好，装上接头护套，将滑触线调平、固紧。依次装好全部滑触线。注意接头处应平滑，间隙<0.5mm Install and clamp sliding-contact wire in bayonet of suspension. After installation and leveling of four pieces of sliding-contact wire, screw nut of suspension tightly. Fix connector into the other end of the first group of sliding-contact wires, and install the second group of sliding-contact wires in accordance with the same method. Connect two pieces of sliding-contact wire by connector, install connector sheath, level and fasten sliding-contact wire. Install all sliding-contact wires in proper order. Make sure to keep smoothness at joints and spacing<0.5mm. |
| 4 |
安装动力输入段 Installation of power input section |
安装预先设计好的输电方式安装动力输入段，一定要旋紧，再装上护罩。 Install power input section as per the power transmission method that has been designed in advance, and make sure to screw it tightly before installation of protection cover. |
| 5 |
装护套固定夹 Installation of sheath retaining clip |
按照设计方案安装固定夹，一线二个（四孔夹）。 Install retaining clip as per design, two clips for each wire (four-hole clip). |
| 6 |
膨胀段和检修段的安装 Installation of expansion section and inspection/maintenance section |
方法同接头的安装，其他位置应按设计方案定。 The method is identical with installation of connector, and other positions are to be determined as per design. |
| 7 |
装端套 Installation of pothead |
在滑触线的两头安装端套，也可在吊挂前先装上。 Install potheads on both ends of sliding-contact wire, it is also allowed to install before suspension. |
| 8 |
检查 Inspection |
整条滑触线安装好后应认真检查，滑触线是否平直，间距是否一致，悬挂架是否旋紧。接头处是否平滑。 After completion of installation of the whole sliding-contact wire, it is necessary to inspect carefully whether sliding-contact wire is straight, whether spaces are identical, whether suspension is screwed tightly, and whether joints are smooth. |
| 9 |
安装集电器及其支架 Installation of current collector and its bracket |
滑触线安装好后，即可安装集电器，按照高度尺寸H（支架中心到滑靴上平面的高度尺寸）和触靴端中心略高些的要求，把支架焊接在移动的设备上，再将集电器依次安装到集电器支架上旋紧固定。检查触靴是否转动灵活，与导线的接触是否良好，否则应进行调整。 After installation of sliding-contact wire, proceed with installation of current collector, in accordance with height dimension H (height from bracket center to upper surface of contact slipper) and requirement that the center of contact slipper side should be slightly higher, weld bracket on mobile equipment, then install current collectors in proper order on collector bracket and screw tightly. Inspect whether contact slipper turns flexibly, whether the contact with conductive wire is good, otherwise it is necessary to adjust. |
| 10 |
集电器的电缆线与用电设备的电缆线接好 Connection of cable of current collector with cable of power consumption equipment |
注意在接线前，应按常规检查电机的各项绝缘要求是否符合要求，若出现异常应检修或更换。 Before wire connection, make sure to inspect whether insulation requirements of electric motor are met, in case of abnormity, it is necessary to inspect, repair or replace. |
| 11 |
接电源 Connection of power supply |
把电源线牢固的接在动力输入段上，注意压紧。 Connect power supply line firmly on power input section, and make sure to press tightly. |
| 12 |
试车 Trial run |
先应空载试车，往复运行几个来回，若无异常即可投入负荷试车，观察电压、电流是否正常，若有异常应立即停车，切断电源，进行检查，故障排除后再投入运行。 Firstly, it is necessary to conduct trial run for several times of reciprocating operation under no load, proceed with under-load trial run if there is no abnormity, observe whether voltage and current are normal, shut down immediately in case of abnormity, disconnect power supply and inspect, and proceed with operation again after elimination of malfunctions. |
